2024 Vermeer® Trommel Screens TR626
- Year 2024
- Make Vermeer®
- Model Trommel Screens
2024 Vermeer® Trommel Screens TR626
Powerful workhorse making short work of processing material.With a 6 ft/1.83 m drum and a hopper that holds 6 cubic yards/4.6 cubic meters, the TR626 makes short work of processing material. Access the drum through removable side panels, drum end or top of the drum. Its 125 hp/93.2 kw John Deere 4045 Tier 4 Final is a powerful workhorse. Impressive 72.5 ft/22.1 m conveyor features self-cleaning tail pulley and return idlers.
Features may include:
Startup delay and alarm systems- Enhance worker safety with startup delay and alarm systems that notify your whole crew when the machine is about to start.
- Move material smoothly without bridging, thanks to a tall, wide throat opening.
- Extend belt life even under tough loading conditions with closely set, heavy-duty rollers supporting the apron conveyor.
- Keep screen weights low when processing wet materials by clamping on a smaller diameter tension screen wire and increasing screening area.
- Speed up your clean up because the flashing and sheeting fit tightly against the drum and conveyors to reduce spillage.
- Forget the loading ramps, since the 626 has a low hopper infeed height.
Motor
Displacement
Conveyor: 629.3 cu-cm | Drum: 48.8 cu in (800 cu cm)
Suspension
Suspension
Leaf spring
Wheels & Tires
Tires, Rear Specification
Option One: 235-75R 17.5H qty. 4
Electric
Electrical
Drum Drive Chain: 140 WT
Operational
Operating Speed
Fines Belt: 123.4 m/min | Apron Conveyor: 0-35 fpm (0-10.7 m/min) | Drum: 0-24 rpm
Hydraulics
Hydraulic Pump
Operation: 15.4 gpm (58.3 L/min) | Drum Operation: 0-42.6 gpm (161.3 L/min) | 62.9 gpm @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa])
Chassis
Frame Type
Description: 4 independent hydraulic jacklegs
Dimensions
Dimensions
Self-Cleaning Return Idlers: 6, each 4" (10.2 cm) diameter | Tail Pulley Takeup: 30.5 cm | Rubber Flashing: Adjustable, .25" (6.44 cm) thick, 4" (10.2 cm) | Head Pulley Bearing: 2.5" (6.4 cm) pillow block | Head/Tail Pulley Type: Rubber-lagged, 12" (30.5 cm) diameter | Brush Diameter: 35.6 cm | Troughing Idler Type: 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers | Drum Angle Adjustability: 0-7 degrees | Drum Diameter: 1.8 m | Drum Support Description: Four steel trunnion rollers 8 in (20.3 cm) diameter | Hopper Opening: 13.2' x 5.3' (4 m x 1.6 m) | Thrust Bearing Diameter: 12.7 cm | Thrust Bearing Face: 7.4 cm | Brush Assembly Support: Two 1.25" (3.2 cm) sealed ball bearings | Self-Cleaning Tail Pulley Dimensions: 10" (25.4 cm) diameter, with 2.4" (6.1 cm) shaft | Head Pulley Type: Rubber lagged, 12" (30.5 cm) diameter | Rubber Flashing: Adjustable, .25" (.64 cm) thick, 4" (10.16 cm) | Self-Cleaning Return Idlers: 11, each 4" (10.2 cm) diameter | Fines Conveyor Frame: 4" x 8" (10.2 cm x 20.3 cm) structural steel tubing
Length
Operation: 25.7 m | Drum: 7.9 m | Apron Conveyor: 4.9 m | Fines Conveyor: 22.1 m
Transport Length
16.6 m
Height
Operation: 4.8 m | Conveyor Belt Stacking: 16.6' (5.1 m) with drum at 4 degrees | Apron Opening: 86.4 cm | Hopper: 9.5' (2.9 m) from ground level at operating incline
Transport Width
287 cm
Width
Operation: 287 cm | Apron Opening: 109.2 cm | Apron Conveyor Belt: 121.9 cm | Drum Support Description: 4 in (10.2 cm) width | Head Pulley Type: 38" (996.5 cm)
Transport Height
4.1 m
Conveyer Width
Conveyor Belt: 91.4 cm
Hopper Width
Bottom: 121.9 cm
Capacities
Volume
Approximately 200 cu yd (152.9 cu m) per hour with .5" (1.3 cm) screens installed and material with moisture less than 40%
Hopper Capacity
4.6 cu m
Fuel Capacity
Tank: 757.1 L
Features
10205.8 kg
Weights
Weight
29483.5 kg | Hitch: 13607.8 kg
Features
Features
Apron Conveyor Rollers: 4" (10.2 cm) diameter qty. 14 | Maximum Screen Panels: 8 | Idler Type: 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers
Construction Material
Bristle: Polyethylene
Belt Type
Conveyor: 220 lb (99.8 kg), 2-ply, 2/16" x 1/16" (4.8 mm x 1.6 mm) / 220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm)
Axle Bearing Extensions, Rear
Leaf spring
Conveyor Type
Fines Conveyor: Part of trailer frame